[Jun 04, 2024] Valid 300-515 Test Answers & 300-515 Exam PDF
Valid CCNP Service Provider 300-515 Dumps Ensure Your Passing
NEW QUESTION # 36 
An engineer is trying to configure an EVPN VWPS. What is the issue with this configuration?
- A. The member in the VPWS context should be the PE-facing interface.
- B. The service instance and the EVPN instance are different.
- C. Interface GigabitEthernet0/1/0 should not have any IP address.
- D. The 12vpn evpn command should be instance 101.
Answer: C
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_l2_vpns/configuration/xe-3s/asr903/16-7-1/ b-mpls-l2-vpns-xe-16-7-asr900/epvn_vpws_single_homed.pdf
NEW QUESTION # 37
Refer to the exhibit:
A network engineer is implementing an OSPF configuration Based on the output, which statement is true?
- A. IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway
- B. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0
- C. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
- D. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
Answer: B
NEW QUESTION # 38
Refer to the exhibit.
A technician is troubleshooting a connectivity issue and notices that there is no IS-IS adjacency between R1 and R2. What can the technician change to bring the IS-IS adjacency up?
- A. Change R1's is-type to level-2-only
- B. Change R2's net address to be in the same area as R1.
- C. Change R2's configuration to no longer set the overload bit.
- D. Change R1's net address to be in the same area as R2.
Answer: A
NEW QUESTION # 39
Which two frames can be configured on an Ethernet flow point? (Choose two.)
- A. of a specific VLAN
- B. with different class of service values
- C. with no tags
- D. with identical type of service value
- E. with different type of service values
Answer: A,C
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/cether/configuration/xe-3s/asr903/16-5-1/b-ce- xe-16-5-asr900/trunk-efp-support.html
NEW QUESTION # 40
Refer to the exhibit. An engineer has configured router 1 to provide shared services to clients behind router 2.
To complete the implementation so that routes from router 1 are accepted, what must the engineer configure on router 2?
- A. with export route targets 301:202 and 101:102
- B. with import route targets 101:102 and 202:201
- C. with export route targets 201:202 and 401:402
- D. with import route targets 201:202 and 401:402
Answer: D
NEW QUESTION # 41
Refer to the exhibit. A network operator is implementing EVPN IRB on PE1. Which two command placements enable the advertisement of Type 2 routes and what information do Type 2 routes contain? (Choose two.)
- A. Type 2 routes contain Ethernet Auto-Discovery information.
- B. Type 2 routes contain inclusive source-specific multicast route information.
- C. Type 2 routes contain MAC/IP information.
- D. The operator adds in "host-routing" under the VRF EVPN.
- E. The operator adds in "host-routing" under the BVI651 interface.
Answer: C,E
NEW QUESTION # 42
Refer to the exhibit. An organization is running H-VPLS on a network comprising four routers in a hub-and-spoke topology with R1 as the hub.
An engineer added a new spoke with multiple VCs to the network, and now traffic cannot flow properly.
How should the engineer update the configuration on R1 to correct the problem?
- A. Disable Cisco Discovery Protocol to allow MPLS to share labels between the designated spokes
- B. Disable Cisco Discovery Protocol to allow for neighbor discovery
- C. Disable split horizon to allow multiple VCs per spoke
- D. Disable spanning tree to allow loops to occur within the hub-and-spoke topology.
Answer: C
NEW QUESTION # 43
Refer to the exhibit.
A customer carrier running MPLS VPN wants to utilize a backbone carrier to forward traffic and exchange VPNv4 prefixes between the two customer carriers networks depicted. Which two sets of routers must establish MP-iBGP sessions? (Choose two.)
- A. CC-PE-A and CC-P-A
- B. BB-PE-A and BB-PE-B
- C. CC-PE-A and CC-PE-B
- D. BB-PE-A and CC-PE-B
- E. CC-PE-A and BB-PE-A
- F. BB-PE-A and BB-P-A
Answer: B,C
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_ias_and_csc/configuration/12-2sx/mp-ias- and-csc-12-2sx-book/mp-carrier-bgp.html
NEW QUESTION # 44
An engineer is troubleshooting an EoMPLS circuit on a Cisco IOS XR router interface that removes a VLAN
- A. interface GigabitEthernet 0/10.10 l2transport
encapsulation dot1q 10
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 2/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - B. interface GigabitEthernet 0/10.l2transport
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - C. interface GigabitEthernet 0/10.10
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - D. interface GigabitEthernet 0/10.10 l2transport
encapsulation dot1q 10
rewrite ingress tag translate 1-to-1 dot1ad 10
symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588
Answer: A
NEW QUESTION # 45
Refer to the exhibit.
A network operator is implementing EVPN IRB on PE1. Which two command placements enable the advertisement of Type 2 routes and what information do Type 2 routes contain? (Choose two.)
- A. Type 2 routes contain Ethernet Auto-Discovery information.
- B. Type 2 routes contain inclusive source-specific multicast route information.
- C. Type 2 routes contain MAC/IP information.
- D. The operator adds in "host-routing" under the VRF EVPN.
- E. The operator adds in "host-routing" under the BVI651 interface.
Answer: C,E
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/iosxr/ncs5500/vpn/61x/b-ncs5500-l2vpn-configuration- guide-61x/b-ncs5500-l2vpn-configuration-guide-61x_chapter_01010.html
NEW QUESTION # 46
While troubleshooting EoMPLS configuration problems, which three parameters should an engineer match between the two ends of the pseudowire configurations? (Choose three.)
- A. control word usage
- B. EFP subinterface number
- C. Xconnect group name
- D. pseudowire ID
- E. MTU size
- F. VLAN name
Answer: A,D,E
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/multiprotocol-label-switching-mpls/mpls/213238-mpls- l2vpn-pseudowire.html
NEW QUESTION # 47
While implementing Layer 3 MPLS VPN, which feature should an engineer use at the PEs to transform the customer IPv4 prefixes into a unique 96-bit prefix?
- A. VC ID
- B. RD
- C. RT
- D. PW ID
Answer: B
NEW QUESTION # 48
An engineer is troubleshooting an EoMPLS circuit on a Cisco IOS XR router interface that removes a VLAN from the distribution layer. Which configuration should the engineer apply in order to accomplish the task?
- A. interface GigabitEthernet 0/10.10 l2transport
encapsulation dot1q 10
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 2/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - B. interface GigabitEthernet 0/10.l2transport
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - C. interface GigabitEthernet 0/10.10
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - D. interface GigabitEthernet 0/10.10 l2transport
encapsulation dot1q 10
rewrite ingress tag translate 1-to-1 dot1ad 10
symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588
Answer: A
Explanation:
Section: Layer 2 VPNs
NEW QUESTION # 49
An engineer noticed that PE3 is failing to accept IPv6 traffic information from PE1 The engineer confirmed that both PE3 and PE1 routers are configured accurately with IPv6 protocol To eliminate IPv6 traffic loss issue, which action must the engineer take to solve the problem?
- A. Configure 6PE that provides global IPv6 reachability over IPv4 MPLS
- B. Disable 6PVE that provides local IPv6 reachability over MPLS.
- C. Configure 6PE forwarding between 6PE routers based on the IPv6 header
- D. Allow PE routers use the MP-iBGP extensions in the IPv6 network configuration to exchange IPv6 reachability information.
Answer: A
NEW QUESTION # 50
Which option is the primary purpose of central service MPLS VPNs?
- A. provide other service providers access to customer resources
- B. provide the provider access to customer resources while ensuring customers cannot communicate directly
- C. provide customer access to provider resources while ensuring customers cannot communicate directly
- D. provide other service providers access to provider resources
Answer: C
NEW QUESTION # 51 
What is the effect of this configuration?
- A. An LSP virtual interface tunnel is created.
- B. A Cisco MPLS TE tunnel is generated with 192.168.1.2 as the source IP address of router 1.
- C. Router 1 accepts multicast routes with a tag of 12:1
- D. The mroute table is cleared.
Answer: C
NEW QUESTION # 52
You try to configure MPLS VPN VRF Selection based on a source IP address on an interface that has VRF configured, but you receive an error.
Which action must you take to correct the problem?
- A. Change the source IP address.
- B. Configure static routes for the VRF.
- C. Add the IP address to the VRF table.
- D. Remove the VRF from the interface.
Answer: D
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/vrfselec.html
NEW QUESTION # 53
Which three functions are performed by the PE router in an MPLS Layer 3 VPN? (Choose three.)
- A. imports and exports RTs that are received from the P routers
- B. exchanges VPN labels with the CE routers
- C. translates the CE routing information into VPNv4 routes
- D. exchanges routing updates with the CE router
- E. exchanges VPNv4 routes with other PE routers over MP-BGP
- F. exchanges RDs with the P routers
Answer: C,D,E
NEW QUESTION # 54 
Drag and drop the EVC configuration items from the left onto the correct descriptions on the right.
Answer:
Explanation:
Explanation
NEW QUESTION # 55
Refer to the exhibit. PE1 and PE2 are exchanging VPNv4 routes for CE1 and CE2, and PE3 contains the default route to the internet. If the three devices are operating normally, which two conclusions describe this configuration? (Choose two.)
- A. Only the CE2 VRF can access the default route provided by the Internet VRF.
- B. All three routers must be running a distance-vector routing protocol.
- C. All three routers must be running MP-BGP.
- D. The CE1 and CE2 VRFs can access the default route provided by the Internet VRF.
- E. The CE1 and CE2 VRFs can exchange routes only between their respective VRFs on PE1 and PE2.
Answer: C,E
NEW QUESTION # 56
An ISP provides a major client MPLS VPN for managed services. The MPLS engineering team needs to use the advanced VPN feature of selective VRF import so that only specific prefixes are present in the required VPNs.
Which aspect of this feature must the team consider?
- A. A route must pass the import route map first and then the route target import filter.
- B. The import-map command is applied under the PE interface that connects to the CE router.
- C. The routers that are imported in the VRF can be BGP and IGP routes, so other match conditions in the route map, besides communities, can be used.
- D. A route is imported into the VRF only when at least one RT that is attached to the route matches one RT that is configured in the VRF and the route is permitted by the import route map.
Answer: D
Explanation:
Reference: https://www.ccexpert.us/mpls/configuring-selective-vrf-import.html
NEW QUESTION # 57
While troubleshooting an AToM L2VPN service, a network consultant notices that the AC Layer 2 encapsulations are different. Which action should the consultant take in order to make the MPLS L2VPN work?
- A. nonrouted interworking setup to properly translate only the Layer 2 information from the AC
- B. tag-rewrite on the ingress and egress PE router
- C. interworking IP configuration on the last PE router before label disposition
- D. interworking IP configuration on both the AC terminations on the PEs
Answer: D
NEW QUESTION # 58
Refer to the exhibit.
Which statement about this output is true?
- A. The adjacent router is the egress LSR and has mpls ldp explicit-null configured.
- B. The adjacent LSR router configured mpls label range 0.
- C. The zero in the second column is the normal behavior of an egress router LSR.
- D. The router IP 192.168.1.2 sent an implicit null, and the output is from the penultimate LSR.
Answer: A
NEW QUESTION # 59
Refer to the exhibit. Router 1 is a P router in the ISP MPLS core.
A connected P router cannot generate an MPLS label for the router 1 loopback0 interface.
Which action resolves this issue?
- A. The network statement under the routing process must have a wildcard mask of 0 0.0 255.
- B. The loopback0 interface must be in OSPF area 0.
- C. A static route to null 0 must be added for the loopback interface and then static routes must be redistributed into OSPF
- D. The OSPF network type must be changed on loopback0 to point-to-point
Answer: A
NEW QUESTION # 60
......
The Cisco 300-515 exam is designed for candidates with intermediate to advanced-level knowledge of network security and VPN technologies, including MPLS, DMVPN, GET VPN, and FlexVPN. It covers a wide range of topics, including VPN routing, deploying and configuring VPNs, troubleshooting VPN connectivity issues, and more.
To take the Cisco 300-515 certification exam, candidates should have a strong understanding of networking concepts and Cisco technologies. They should also have experience with service provider VPN technology implementation and troubleshooting. 300-515 exam is intended for network engineers, network architects, and network administrators who work in service provider environments.
300-515 Dumps Real Exam Questions Test Engine Dumps Training: https://2cram.actualtestsit.com/Cisco/300-515-exam-prep-dumps.html