VALID D-PDD-DY-23 Exam Dumps For Certification Exam Preparation
D-PDD-DY-23 Dumps PDF 2025 Strategy Your Preparation Efficiently
NEW QUESTION # 30
When the PowerProtect DD system boots up for the first time, the CLI configuration wizard script does not start automatically.
Which command can be used to start the script manually?
- A. config wizard
- B. setup config
- C. config setup
- D. configure terminal
Answer: C
NEW QUESTION # 31
A backup administrator needs to implement BoostFS for Windows.
What do they need to install on the Windows server?
- A. CBFS
- B. FUSE
- C. NFS
- D. CIFS
Answer: D
NEW QUESTION # 32
A PowerProtect DD appliance with two expansion shelves is being installed in a customer-provided rack.
When cabling the controller to the shelves, what is connected to the host port on the last shelf in the chain?
- A. Expansion port of the upstream shelf
- B. Host port of the controller
- C. Host port of the downstream shelf
- D. Expansion port of the controller
Answer: D
Explanation:
In a PowerProtect DD system, when setting up expansion shelves, the cabling follows a specific sequence to ensure proper communication between the controller and the shelves. The host port on the last shelf in the chain is connected to the expansion port of the controller to complete the loop. This ensures that data flows correctly between the controller and all shelves in the chain.
NEW QUESTION # 33
Which are two attributes of PowerProtect High Availability? ( Select 2 )
- A. Power Protect DD nodes are configured in active active mode
- B. single set of shared storage is used
- C. supported only on DD9900 systems
- D. PowerPotect DD nodes should have dual heads
Answer: A,D
NEW QUESTION # 34
Task 6
A backup administrator finished installing a PowerProtect DD3300. After the installation, they notice disk 1.5 is offline after running the disk fail command in the DDOS CLI.
Using the simulator, flash an LED on the hard drive with the issue and return it to operation.
When you have finished, continue to the next question.
Answer:
Explanation:
See the solution in the explanation below.
Explanation:
To flash an LED on a hard drive and bring a disk back online using the DD System Manager or DDOS CLI, follow these general steps:
Step 1: Identify the Disk
* In DD System Manager:
* Go to the Hardware section in the sidebar.
* Locate the list of disks, and find Disk 1.5 (the offline disk).
* In DDOS CLI (if using CLI):
* Use the command to list disks and confirm the status of Disk 1.5.
* Command example: disk show state or disk show summary.
Step 2: Flash the LED on the Disk
* In DD System Manager:
* In the Hardware section, select Disk 1.5.
* Look for an option like Flash LED or Locate Drive to help identify the physical disk.
* Activate the LED flash to identify the disk physically.
* In DDOS CLI:
* Use the command: disk locate 1.5 to flash the LED for Disk 1.5.
Step 3: Bring the Disk Back Online
* In DD System Manager:
* After identifying the disk, check for options to Bring Online or Reactivate Disk 1.5.
* Select the option to return the disk to operation.
* In DDOS CLI:
* Use the command: disk unfail 1.5 to bring the disk back online.
Step 4: Verify the Disk Status
* Confirm in DD System Manager or by using the disk show state command in CLI that Disk 1.5 is now online and functioning.
After completing these steps, the LED should flash to help locate the disk physically, and then Disk 1.5 will be returned to an operational state. Let me know if you need further guidance!
A screenshot of a computer Description automatically generated
NEW QUESTION # 35
An administrator is scaling Cloud Tier for a DD9900 by adding a second cloud unit.
What is the required amount of metadata storage (TB)?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 36
When following Dell recommendations what adjustments should a customer make on the Microsoft Windows client when using CIFS on a PowerProtect DD appliance?
- A. Adjust session timeout values and SNMP parameters.
- B. Adjust session timeout values and TCP/IP parameters.
- C. Adjust NTP parameters and SNMP parameters.
- D. Adjust SNMP parameters and TCP/IP parameters.
Answer: B
NEW QUESTION # 37
Which port/protocol is used when using a syslog server to monitor a PowerProtect DD system?
- A. 2051/UDP
- B. 2051/TCP
- C. 514/TCP
- D. 514/UDP
Answer: D
NEW QUESTION # 38
What can be used to monitor system utilization?
- A. system show performance command
- B. system status command
- C. Health tab in the System Manager GUI
- D. Alert Messages
Answer: D
NEW QUESTION # 39
Which product provides air-gap and minimizes the impact of a cyber-attack using a PowerProtect DD system?
- A. NetBackup
- B. PowerProtect Cyber Recovery
- C. PowerProtect Data Manager
- D. CyberSense
Answer: B
Explanation:
PowerProtect Cyber Recovery is designed to protect critical data from cyber threats by creating a secure, isolated environment (an air-gap) where backups can be stored. This air-gapped solution minimizes the impact of a cyber-attack by ensuring that critical data is inaccessible to attackers, even if they breach the main network. In the event of an attack, clean data from the secure vault can be used to restore the system to its pre- attack state.
NEW QUESTION # 40
Which is the default IP address assigned to PowerProtect DD iDRAC?
- A. 192.168.10.100
- B. 192.168.100.100
- C. 192.168.0.120
- D. 192.160.1.120
Answer: C
Explanation:
The iDRAC (Integrated Dell Remote Access Controller) for PowerProtect DD appliances is typically set to this default IP address, allowing administrators to access the management interface for remote management and monitoring. This IP address can be changed as needed to fit the network configuration.
NEW QUESTION # 41
A backup administrator needs to add capacity to a file system. After the installation of an ES40, they need to verify the total amount of data stored before data reduction.
Which command would be used to verify this information?
- A. filesys show summary
- B. enclosure show summary
- C. filesys status
- D. filesys show space
Answer: D
NEW QUESTION # 42
An administrator must display the compression statistics for all files and directories in the file system for the last 7 days and the last 24 hours. Which command is used to gather this information?
- A. storage show
- B. mtree show
- C. filesys report
- D. quota show
Answer: C
Explanation:
Explanation: The filesys report command provides detailed compression statistics, essential for administrators to monitor storage efficiency over time. This insight into compression ratios aids in storage optimization and management planning on PowerProtect DD systems.
NEW QUESTION # 43
What are the steps to configure the Retention Lock Compliance?
Answer:
Explanation:
NEW QUESTION # 44
What is the correct order of steps to verify DD Boost implementation and clone functionality?
Answer:
Explanation:
Explanation:
NEW QUESTION # 45
What action needs to be taken to create the iDRAC users on the Compliance Retention Lock PowerProtect DD?
- A. user idrac create
- B. user create idrac [username]
- C. Use the iDRAC GUI
- D. user add [username] role idrac
Answer: A
NEW QUESTION # 46
......
Latest Verified & Correct D-PDD-DY-23 Questions: https://2cram.actualtestsit.com/EMC/D-PDD-DY-23-exam-prep-dumps.html